Xtreme Gravel Lock VDW 520 11 lbs

Pressure washer Friendly

Easily Cleanable! Epoxy Mortar is known for its exceptional strength and durability. It forms a robust and resilient bond between tiles, providing superior resistance to cracking, staining, and other forms of damage. With this gravel lock, your project can last the test of time!

Highly Water – permeable

Epoxy mortar is an environmentally friendly choice for tile installations. It is made with eco-friendly materials that reduce its impact on the environment. This allows water to pass through. This is important in freeze/thaw climates where durability is normally affected.

Very High Resistance to yellowing

It can withstand anything from heavy foot traffic and moisture to UV exposure and chemicals. This makes it ideal for high-traffic areas and outdoor applications. With this gravel lock, your project will stay beautiful for years to come!

High UV Resistance

Included in its strengths is that the epoxy has the ability to avoid degradation caused by the absorption of UV radiation. This will allow your project to stand the test of time for much longer. Especially while being in consistent sunshine.

Technical Data

Installation Instructions for Xtreme Gravel Lock (VDW 520)

1. Construction Site Requirements

• • A stable and well-compacted gravel/sand bedding layer.

• • The depth of the PHNA Xtreme Gravel Lock should be a minimum of 1.5″ after compaction and finishing.

• • The product must be laid on a permeable concrete or mortar bed
    • • We recommend the PHNA Xtreme Trass Bedding Compound (vdw 480).

• • All elements must be correctly designed and installed for the anticipated traffic loads and in accordance with ASTM.

• • The Xtreme Gravel Lock cannot be used to compensate for any settlement of the sub-structure.

2. Preparation

• • Clean the base material and any joint sides to ensure no contaminants or uncompacted materials are present.

• • Mask any adjacent areas that are not to be jointed in order to prevent any spots or staining from the epoxy.

• • We recommend a test area be prepared, particularly with any sensitive materials, before installation.

• • Any dirty or dusty aggregates should be washed thoroughly and dried before mixing to avoid discoloration and/or loss of strength.
    • • Aggregate may be damp but cannot be wet.

3. Mixing

• • Heavy-duty paddle/drill mixer or suitable gravity mixer, large mixing tub, shovel, screeding tolls, and trowels.

• • Add the appropriate amount of aggregate into the mixing tub or gravity mixer.

• • Followed by the appropriate amount of both A & B components of the Xtreme Gravel Lock.
    • • (The 5kg units of Xtreme Gravel Lock will have 1/4 markings on each bottle, each 1/4 to be mixed with a maximum of 60 lbs. aggregate.)

• • Mix for 5 minutes until homogeneous.

• • For large areas where mixing more than 60 lbs. at one time may be necessary.
    • • We recommend using a gravity mixer.

• • Ensure the mixer is clean and has not been previously used to mix concrete or mortar.

• • If using a gravity mixer, also adhere to the 5 minute mix time.

• • Then, the material can be transferred to a clean wheelbarrow for transportation if needed.

4. Application

• • Apply the freshly mixed material onto the prepared substrate.

• • Spread and level off with appropriate screeding tools or a trowel, then compact and smooth the surface with a trowel.

• • Material may get sticky and more difficult to work with after 30 minutes or in higher temperatures.

5. Important Instruction

• • Remain off the freshly applied areas and protect them from heavy rain for a period of min. 24 hours. Then, the areas can be walked over carefully.
    • • In general, a strength test should be carried out before final clearance of the area after 7 days.

• • The practice has shown that there are minerals for which the epoxy used can produce special effects such as darkening.
    • • Over time, this weathers off, and the mineral substance regains its natural color.

• • In covered areas, the weathering process takes longer.

• • With bright white minerals, a slightly yellowish color change may occur.
    • • Color differences may occur until curing is complete, especially with strongly varying UV radiation.
    • • These phenomena result from the contact between Xtreme Gravel Lock epoxy and mineral aggregate and are not a design defect.

• • The gloss effect remaining after application will degrade over time from exposure to natural UV light.

• • Despite careful processing, marginal detachment of individual grains cannot be ruled out.